WOOD Rx
Original Formula
Product #610
Longest Lasting Wood Stain & Sealer

WOOD Rx is, by far, the best prescription for any wood surface.  It is a technologically advanced, water based finish that effectively penetrates, seals and protects exterior wood surfaces.  WOOD Rx resists moisture penetration and retards the aging (silvering) process of new wood.  It contains an effective fungicide which resists mildew growth on the film and a powerful UV screener which filters out the sun’s harmful rays.  WOOD Rx protects and beautifies wood surfaces 3-5 times longer than conventional, competitive wood sealers.   WOOD Rx original is available in an array of transparent and semi-transparent.

RECOMMENDED USES:
For use on virtually all properly prepared, exterior wood surfaces such as decks, docks, sidings, specialty hardwoods, pressure treated lumber, garden furniture, playhouses and log/timber frame homes.   Contact an INSECO representative for detailed specifications.

SURFACE PREPARATION:
Dirt, grease, grime and any foreign material should be removed before applying WOOD Rx.  Be sure surface is clean and dry.
1. Apply a solution of 1 part household bleach or bleach alternative, 1 part dishwashing soap and 4 parts
    water.
2. Scrub and/or pressure wash as necessary to remove any surface contaminants. 
3. Apply a test sample of WOOD Rx to insure proper adhesion and an appealing appearance.  If beading
    or crawling occurs, contact INSECO prior to applying.

APPLICATION:
1. Stir WOOD Rx thoroughly before use.  
2. Apply with a brush, roller or airless sprayer
3. Two thin coats are recommended for maximum performance.  The second coat may be applied as soon  
    as the first coat is dry to the touch.  The surface must be dry to apply the second coat. 
3. Do not apply in direct, hot sunlight or when surface temperatures are below 50 deg. F.  If surface is hot  
    and dry, cool down with clean, fresh water and apply WOOD Rx to cool, moist surface.  Avoid runs on  
    vertical surfaces and puddles on horizontal surfaces.  Take care to avoid “lapping.”  Always work with a
    wet edge and with the grain of the wood.  Do not stop in the middle of a board and try to come back later
    to pick up where you left off.  Stop at a logical break point to avoid the possibility of creating lap marks.    

CLEAN UP:
Clean up drips and spills immediately using a damp cloth.  Clean tools and equipment with soap and fresh water. 

CAUTION:
Do not apply if the threat of rain exists.  Keep from freezing. Keep out of reach of children. 

TECHNICAL DATA:
Finish: Satin                                                                         
Pigment Type: None
Vehicle Type: 100% Acrylic                                             
Solvent Type: Water
% Solids By Weight: 20% +/- 2%                                    
Flash Point, Minimum: Not Flammable
% Solids By Volume: 19% +/- 2%                                  
Density: 10.86 lbs. Per gallon
Viscosity @ 75 deg. F (24 deg. C): 65-75 K.U.
V.O.C. : Less than 150 g/l

Average Dry Time @ 75 deg. F (24 deg. C): Touch 30 minutes.  Recoat 2-4 hours.  Foot traffic 24 hours.

Flame Spread: Class A rating on non-combustible substratum

Coverage (Theoretical): Coverage will depend on porosity and contour of the surface being coated.  Coverage typically averages 250-350 square feet per gallon.  Two coats are always recommended for maximum performance. 

RESISTANCE TO:
Weather/UV: Excellent
Moisture Penetration: Excellent
Peeling/Flaking/Blistering: Excellent
Mildew: Excellent

Technical data contained herein is true and accurate at the date of issue, but is subject to change without notice.  An INSECO representative should be contacted with any questions concerning product information or application procedures.  Our products conform to INSECO quality standards, but no other warranty is expressed or implied.  Liability, if any, is limited to the replacement of product or purchase price.